Electric Water Heater Installation
MrNams Published on Aug 05, 2017

#MrNams Subscribe: https://goo.gl/mqbdai Facebook: https://www.facebook.com/MrNamsOfficial Twitter: https://twitter.com/MrNams Hello friends, Hope you all doing well! Hello friends, in this video I shall try to show how to Install an Electric Water Heater also called as electric geyser. You will need following materials and tools: 16 amp plug, Teflon tape, tee with three Nipples connected, two hot water Connection Pipes Steel Ribbed, wire striper and screw driver, Bolts (Coach Screws) & washers to fit heater on wall, Drilling Machine, nail hammer, snap and grip wrench Procedure 1) Unbox electric water heater. 2) Wire water heater a plug, remember to connect, blue wire to earth terminal, black wire to neutral and red like wires to phase. 3) Mark positions to drill, mark the spots to drill by making a hole with pen 4) Compare drill bit with Rawl Plug , and insert the required drill bit into a power drill, and firmly lock it, then make pilot drills at marked positions 5) Insert the plugs into the pilot holes 6) Insert the tip of the screw into the installed wall plug, then gently twist the head of the screw in between your fingers until the tip enters the first few millimetres of the plug,and add nuts 7) Insert appropriate screw driving bit into power drill and firmly lock it, then Drive all screws using a power drill machine 8) Install water heater 9) Connect hot water pipes to both inlet and outlet of water heater, and properly tighten both pipe nuts. 10) Disconnect the water supply line, and remove plastic PVC threaded pipe plug. 11) Use Teflon tape to seal the angle valve nipple threads, Imbed the tape in an anti-clockwise direction. 12) Connect Tee to angle valve, and install tee connected angle valve. 13) Connect hot water pipes to both nipples of tee, connect all pipes and tighten nuts using adjustable wrench, plug pin into socket. Inlet water working: When solar water available, then solar water will flow to wards tee, switch off angle valve, attached with tee, to avoid, mixing of solar water and cold water, so that water continues to flow to heater, hot water from heater goes to tap and shower When no solar water available then simply, turn off solar water angle valve and turn on cold water angle valve, so that cold water will go to heater, see cold water will not be goo into solar water as we switched off solar water angel valve, Cold water continues to flow to heater and hot water from heater to tap and shower This video might answers following queries - How to install water heater - how to install water heater in bathroom - how to install water heater electric - how to install water heater shower - how to install water heater expansion tank - how to install water heater straps - how to install water heater tank - how to install water heater switch - how to install water heater vent - Water heater installation - Water heater at home - Water heater geyser - Water heater working - instant water heater - water heater - storage water heater THANKS FOR WATCHING. If you enjoyed video, please do like, share and comment. Please SUBSCRIBE to follow new Uploads https://goo.gl/mqbdai WARNING: Always be safe, everything you do is at YOUR OWN RISK! I shall not be liable for any injuries, loss or damages claimed to be caused by watching the contents either. #mrnamsofficial #instagram #reels #instagood #craft
Comments ( 1)
  • MrNams Published on Feb 25, 2022 <b>Click below link to subscribe,it&#39;s absolutely free.</b><br><b><a href="https://goo.gl/mqbdai">https://goo.gl/mqbdai</a></b><br><b>सब्सक्राइब करण्यासाठी वरील लिंकवर क्लिक करा,ते पूर्णपणे मोफत आहे.</b><br><b>सब्सक्राइब करने के लिए ऊपर दिए गए लिंक पर क्लिक करें, यह बिल्कुल फ्री है|</b> 0